DC Circuit Water Analogy

This is an active graphic. Click any part of it for further details.

In a direct current (DC) electrical circuit, the voltage (V in volts) is an expression of the available energy per unit charge which drives the electric current (I in amperes) around a closed circuit. Increasing the resistance (R in ohms) will proportionately decrease the current which may be driven through the circuit by the voltage.

Each quantity and each operational relationship in a battery-operated DC circuit has a direct analog in the water circuit. The nature of the analogies can help develop an understanding of the quantities in basic electric ciruits. In the water circuit, the pressure P drives the water around the closed loop of pipe at a certain volume flowrate F. If the resistance to flow R is increased, then the volume flowrate decreases proportionately. You may click any component or any relationship to explore the the details of the analogy with a DC electric circuit.

Ohm's lawVoltage lawCurrent lawPower relationship
Basic DC circuit relationships
Index

DC Circuits
 
HyperPhysics***** Electricity and Magnetism R Nave
Go Back





Voltage-Pressure Analogy

A battery is analogous to a pump in a water circuit. A pump takes in water at low pressure and does work on it, ejecting it at high pressure. A battery takes in charge at low voltage, does work on it and ejects it at high voltage.


Water analogy to DC circuits
Index

DC Circuits
 
HyperPhysics***** Electricity and Magnetism R Nave
Go Back





Current-Flowrate Analogy

Volume flowrate in liters/min, cm3/sec, m3/sec, etc. Electric current flow in coulombs/sec = amperes.

A large pipe offers very little resistance to flow, as shown by Poiseuille's law.

A wire offers very little resistance to charge flow according to Ohm's law.

Connecting a battery to an appliance through a wire is like using a large pipe for water flow. Very little voltage drop occurs along the wire because of its small resistance. You can operate most appliances at the end of an extension cord without noticeable effects on performance.

Water analogy to DC circuits
Index

DC Circuits
 
HyperPhysics***** Electricity and Magnetism R Nave
Go Back





Resistance to Flow

The resistance to flow represented by a severe constriction in a water pipe is analogous to the resistance to electric current represented by a common electric "resistor".

The severe constriction will have more resistance than the remainder of the pipe system. Likewise a resistor in an electric circuit will generally have much more resistance than the wire of the circuit. If the single elements represented are the only resistances in the circuit, then essentially all the pressure or voltage will drop across these single elements. The fact that essentially all the voltage drop appears across a resistor or an ordinary electrical appliance makes possible the operation of such appliances from an extension cord, or the operation of several appliances in parallel on a single circuit in your home.

Water analogy to DC circuits
Index

DC Circuits
 
HyperPhysics***** Electricity and Magnetism R Nave
Go Back





Ground-Reservoir Analogy

The function of a ground wire in an electric circuit is in many ways analogous to the reservoir attached to the water circuit. Once the pipe is filled with water, the pump can circulate the water without further use of the reservoir, and if it were removed it would have no apparent effect on the water flow in the circuit.

The reservoir provides a pressure reference, but is not part of the functional circuit. Likewise, the battery can circulate electric current without the ground wire. The ground provides a reference voltage for the circuit, but if it were broken, there would be no obvious change in the functioning of the circuit. The ground wire protects against electric shock and in many cases provides shielding from outside electrical interference.

This view of a ground is not adequate to explain the function of an appliance ground wire because just a connection to the earth is not sufficient to trip a circuit breaker in case of an electrical fault. To be effective in preventing shock hazards, an appliance ground must connect back to the supply through the neutral wire.

Nevertheless, the image of the earth as a charge reservoir is helpful in understanding the energetics of the entire electrical supply system. At a power plant, charge can be drawn from the earth and the generation process does work on the charge to give it energy. This energy is described by stating its voltage (1 volt = 1 joule/coulomb = energy/charge). The energy can be transported cross-country at high voltages and then supplied to end users at lower voltages with the use of step-down transformers. The energy can then be used and the charge discharged to the earth. The charge upon which the work is done at the power plant does not have to be transported cross-country, and the "spent" charges do not have to be transported back to the power plant, but just dumped into the "reservoir".

Water analogy to DC circuits
Index

DC Circuits
 
HyperPhysics***** Electricity and Magnetism R Nave
Go Back